Copper and Lead Free Mirror
Manufacturer of custom glass mirrors and glass mirror with 3-6mm thickness. Factory direct supply offering OEM and bulk services.
View product
Sourcing safety glass across borders is really a decision about who stays accountable for tolerances, packing and paperwork: an in-house tempered glass manufacturer controls the furnace, the edge line and the packing bench, while a trading-side tempered glass supplier usually resells that capacity and adds one more hand-off to the chain. This guide converts that difference into a scored vetting process, a certification matrix and a product-level proof point you can check against the 10mm clear tempered glass specification.
Each route prices, schedules and guarantees work differently. Decide which one your project actually needs before you open a single quotation, because the answer changes what you should ask for in writing.
Owns the tempering furnace, the edging line and the packing area.
Quotes fast and aggregates several plants, but tempering and packing are subcontracted.
Buys tempered sheets or cut panels and adds measurement, fitting and installation.
Score any candidate supplier from 0 to 5 on each point. A total under 40 signals a supplier you will spend time correcting; 50 and above is a supplier that can carry a repeat programme. Expand each point to see what a strong answer sounds like.
Match the standard to the destination first, then request the document that proves it. The four standards below are the ones documented for item LYD-CTG10; confirm the applicable one for your project before ordering.
| Standard | Region served | What it covers | Document to request | How to verify |
|---|---|---|---|---|
| CE EN 12150-2:2004 | Europe | European product standard for thermally toughened soda lime silicate safety glass | Declaration of conformity plus the supporting test report | Check that the thickness and finish on the document match your order |
| ANSI Z97.1-2015(R2020) | United States | Safety performance specification and test methods for safety glazing used in buildings | Safety glazing test report referencing the 2015 revision | Confirm the report is the R2020 reaffirmed revision, not an older edition |
| CAN/CGSB-12.1-2022 | Canada | Canadian safety glazing standard covering tempered glass used in building applications | Test report against the 2022 edition | Check the edition year — earlier editions are frequently quoted by mistake |
| CPSC 16 CFR 1201-2024 | United States (federal) | Federal safety standard for architectural glazing materials, including impact categories | Impact test record naming the category achieved | Match the category to the location the glass is installed in |
Before you accept any certificate: check three things — that the standard edition year is current, that the document names the thickness and finish you are buying, and that the producing plant on the document is the plant that will actually temper your panels.
The scorecard above is only useful if a supplier can answer it with a real item. This is that answer: the published specification for LYD-CTG10, produced under factory-direct supply with OEM programmes for shower doors and plates.
| No. | LYD-CTG10 |
|---|---|
| Thickness | 10mm |
| Edge processing | Flat edge and polished |
| Standards | CE EN 12150-2:2004; ANSI Z97.1-2015(R2020); CAN/CGSB-12.1-2022; CPSC 16 CFR 1201-2024 |
| Minimum size | 100mm × 100mm |
| Maximum size | 3660mm × 2440mm |
| Port of loading | Xingang port |
| Packing | Plywood crates, A-steel racks etc. |
The one rule that decides your drawing: tempered glass cannot be cut or altered after the tempering process, so every dimension, corner and cut-out must be frozen before production begins. Pricing, weight values and lead times are confirmed per order in your quotation.
Understand the process and you can write an inspection request that a supplier cannot answer vaguely.
Different applications pull different details out of the same 10mm item. Use this table to move from a use case to the exact points your RFQ must settle.
| Your scenario | Why 10mm clear tempered glass fits | Confirm before the RFQ |
|---|---|---|
| Frameless shower door or enclosure | 10mm panel with flat polished edges and safety break behaviour; the page names shower door panels as a core application | Hinge, handle and cut-out positions — no drilling is possible after tempering |
| Office or retail glass partition | Clear finish transmits natural light without sacrificing mechanical strength | Which standard your destination requires and whether the top edge is exposed or framed |
| Balcony or staircase railing | Used as an interior and exterior structural component with polished edges | Local building code, fixing method and whether a laminated build-up is specified instead |
| Table top, shelving or furniture glass | Produced down to 100mm × 100mm and up to 3660mm × 2440mm, so small and large pieces share one order | Support hardware and edge finish — panels can be heavy, so support structures matter |
| Facade or skylight glazing | Tolerates high pressure and significant temperature fluctuation | The full assembly specification with your engineer, not the glass alone |
| Exterior architectural cladding | Suited to exterior structural components and easy to clean, with coatings available to reduce water spotting | Finish choice — clear, frosted, tinted or patterned — and its availability for your order |
A complete enquiry reaches a real price faster than a one-line message. Include all eight points and your quotation can be prepared without a round of clarification.
LYD-CTG10 is offered through factory-direct supply with OEM programmes for tempered glass shower doors and plates, and dimensions are customised for complex design requirements. If your project needs a mock-up, a mixed container or a repeat programme, say so in the first message so the quotation is built around it.
Panels ship in plywood crates or A-steel racks and load at Xingang port.
Request a QuoteAsk who runs the tempering furnace. A manufacturer can describe its own heating and cooling cycle, its edge line and its packing bench, and can name the standard its process is documented to. A trading supplier usually resells that capacity, so ask for the producing plant's name, its test reports and its loading port before you compare prices.
The product page lists CE EN 12150-2:2004, ANSI Z97.1-2015(R2020), CAN/CGSB-12.1-2022 and CPSC 16 CFR 1201-2024 for item LYD-CTG10. Request the matching declaration or test report for the thickness and finish you actually order.
LYD-CTG10 is produced from a minimum of 100mm × 100mm up to a maximum of 3660mm × 2440mm. Because tempered glass cannot be cut or altered after tempering, every dimension and cut-out must be confirmed before production starts.
Edge processing is flat edge and polished. The page also describes clear, frosted, tinted and patterned glass types, so state the finish you need in your enquiry and have it confirmed on the quotation before you commit.
Packing options include plywood crates, A-steel racks and similar configurations, and the port of loading is Xingang port. Ask for packing and container-loading photos as part of your pre-shipment inspection.
Pricing for LYD-CTG10 is quote-based — there is no online checkout for this product. Send your drawing or size list, thickness, finish, edge treatment, quantity, destination port, applicable standard and target date through the contact page, and the team will confirm supply and pricing for your order.
Keep adjacent product options together for a faster catalog comparison.
Manufacturer of custom glass mirrors and glass mirror with 3-6mm thickness. Factory direct supply offering OEM and bulk services.
View product
Safety Backed Mirror With CAT I Or CAT II Film Safety Mirror is produced by covering and adhesive PE （vinyl film）on the back all kinds of mirrors,are widely demanded in North Ameri
View product
Manufacturer of custom glass mirrors with thickness 3-12mm. Offers factory direct supply and OEM services for premium mirror glass solutions.
View productreview the product details, images, and specifications presented on the official product page.
use the application and use-case information published on the official product page.
confirm the specifications and options listed for the exact product variant before placing an order.
check the official product page or ask the supplier about options shown for the selected product.
use the official contact or inquiry path provided on the site.
include the product page, intended use, required quantity, and any specifications you need the supplier to review.
